KT295 | GAC 295 Installation Kit - Spare (Included with Actuator) - Rack Linkages, Hardware

24VDC / Standard Unit

5.0 in. [127mm] Thread Length / #8-32NC-2A Thread Stud Terminals / High Output 1.3kΩ

2.37 in. [60mm] Thread Length / 1 ft. [0.3m] Harness / Flying Leads / Aluminum Clear Anodized

24VDC / Packard Connector without Mating Connector / Single (ADD) or Double Rack Bearing (ACD) / Bosch Install Kit KT289 (ADD) or BYC ASIMCO KT283 (ACD) Included

24VDC / Military-Style Connector without Mating Connector / Note - Compatible with EEG6500 Series

10 Turn / 20KΩ / With Locking Shaft

Multi-VDC / Replacement for Most ESD5500E Series in a Single Unit

Basic Engine Controller / Crank Pause and Overspeed Switch / Preheat Capabilities / Keyswitch

MSP / Engine Speed Simulator, Alligator Clips, General Usage

Multi-VDC / Military-Style Connector without Mating Connector / Die-Cast Housing

24VDC / Commercial Connector with Mating Harness CH251-2134 7 ft. [2.13m] / High Temperature Coil for Full Duty Cycle Operation / Not equivalent to Renault 5010438374 which has Saab Connector (Contact GAC for Renault Version)

ACB, ADB, ATB-T4 Military-Style (Amphenol) Actuators - 12 ft. [3.6m] Harness / 90° Connector EC1010 / 6-Terminal

24VDC / Interface Module Scania S6 (EMS) EFI SY to GAC LSM/SYC / Nominal 5VDC Input / 1.6VDC Output

DPG100/101-F & DFT200 Handheld Configuration Tool

275 Installation Kit - MTU - Bosch P 3000 Bearing Retainer Kit - Plate, Gasket, Seal, Shims, Hardware

24VDC / Packard Connector without Mating Connector

10VDC (From Speed Control) / Variable Speed - Off-Road

24V / ADC225S with Integrated EDG6000 / Requires EC1502 or CH1520 (Not Included)

2.7 in. [69mm] Thread Length / 6 in. [152mm] Harness / Male Push-On Terminals

Multi-VDC / Automatic Synchronizer with Sync Check Relay

Multi-VDC / Standard Unit

24VDC / Universal - Caterpillar & Cummins / 4-20mA or 0-5VDC Load Sharing Input / 100% Max Duty Cycle Output

MSP Packard Sensors - Connector Kit Replacement / 2-Terminal

M6 Thread Precut to 8.75 in. [222mm], Zinc Plated

USB to RS232 Adapter for PC Interface, GAC Recommended

10VDC (From Speed Control) / Basic Isochronous Load Sharing / Load Anticipation / Droop

12VDC / Packard Connector without Mating Connector / Kubota Super 05 Series D905, D1005, D1105, D1105-T, V1305, V1505, V1505-T & V3 Industrial Series V3300, V3600, V3600-T, V3800 (not DI-T)

Multi-VDC / Built-In Display / Terminal Strip - SUPERCEDED BY EEG6500, SERVICE ONLY

24VDC / Includes - EAM212 (Lean Burn Adapter), Wideband UEGO Sensor Bosch LSU4.2, Harnesses, 12-24V DC/DC Converter (PCI106)

Multi-VDC / Standard Unit

ACE275K, ACE295F, ATBT2/T3-F (AB Position Sensor) Actuators - 6 ft. [1.8m] Shielded Harness with EC1515 / 6-Terminal

4A / 63V Field / Rear Facing Pots / Replaces Basler AVC63-4D & BE350, McPherson SS350, and Marathon SE350

10 Turn / 10KΩ

24VDC / Standard Unit with Idle

3.19 in. [81mm] Thread Length / 2.75 in. [70mm] Harness / Automotive Connector / Stainless

2.37 in. [60mm] Thread Length / 6 in. [152mm] Harness / Male Push-On Terminals / Aluminum Gold Anodized